ATON DLA4 PDF

Search among more than user manuals and view them online Find great deals for Aton DLA4 Four Room Speaker Switch With Volume Control. Shop with confidence on eBay!. Free Shipping on many items across the worlds largest range of Aton Dla4 In Home Audio Equalizers. Find the perfect Christmas gift ideas with eBay.

Author: Vogor Tolrajas
Country: Bahamas
Language: English (Spanish)
Genre: Life
Published (Last): 22 September 2008
Pages: 364
PDF File Size: 19.17 Mb
ePub File Size: 10.76 Mb
ISBN: 811-2-63876-812-2
Downloads: 52540
Price: Free* [*Free Regsitration Required]
Uploader: Digis

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in zton particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and xton, the user is encouraged to try to correct the interference by one or more of the following measures: Increase ddla4 separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit sla4 from that to which the receiver is connected. Protect the power supply cord from being walked on or pinched, particularly at plugs, outlets and the point where they exit from the apparatus.

Severe personal injury and equipment damage can result by not following proper procedures. Follow these guidelines to ensure your device is preserved and protected. Do not apply excessive amplification. ATON atton recommends that you do not add more speakers than recommended. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat. Please report the problem to your dealer immediately.

ATON DLA4 Stereo Receiver User Manual

You will lose any product warranty on the unit. Push a button – your speakers come on. Push it again – they go off. Turn a knob, and the volume goes up or down.

Good exercise, too – especially when your system is located downstairs or on the other side of the house. Use the optional RF remote to turn the volume down in their room instantly from the den. At bedtime, turn off the audio throughout the entire house.

Add an optional RF remote and receiver in order to have full control anywhere in the house. For more information and purchase options, dla44 our website at: Figure and Table provide descriptions and locations of Front Panel controls and indicators.

  LINEAR CONTROL SYSTEM BY B S MANKE PDF

Aton DLA4 Four Room Speaker Switch With Volume Control | eBay

Figure and Table provide description and location of Rear Panel connections. This is a single-source application: Like the previous example, a pair of speakers are connected to the DLA2s Room 1 Speaker Outputs, while an additional pair of speakers is connected to the Room 2 Speaker Outputs. This is a multi-source application: Set the Zone 2 volume level to the point where it achieves the maximum listenable level prior to distortion.

This application provides independent control of each area within a sub-zone. Turn power for the output device OFF before making connections.

Cut the ends of the wire to length, allowing some free play about 6 inches of slack to allow for movement when physically connecting atton wire. Lift up each ip-lock connector until it is dka4 in the up position. Make sure to match the impedance of the speakers and ampliers as noted. Provisions exist for IR, Ground, and Voltage. Speakers rated between 4 Ohms and 8 Ohms can be matched with ampliers also rated from 4 to 8 Ohms.

Most speakers are 4 or 8 Ohms.

When using this setting, maximum volume is reduced to 10 steps. Volume Status Bar Figure If the volume level prior to turning the room off is lower or equal to the Maximum Turn-On Volume Level, the room will come back on at the last volume. If the volume level prior to turning the room off is higher than the Maximum Turn-On Volume Level, the room will come back on at the Maximum Turn-On Volume Level instead of the last volume. Press the Room Button for the desired room. Without releasing the Room button, press and hold the Atkn – Button.

Setting the Maximum Turn-On Volume Level to the highest volume level will essentially disable Maximum Turn-On Volume the room will always come back on at the last volume level prior to turning the room Off. Adjust the volume as required. Ayon set a Scene Preset: Set the volume in each room to the desired level.

Once the Scene Preset has been saved, the Room LEDs for the rooms included in the Scene Preset will blink on and off four times and the system will return to the levels prior to qton the Scene Preset. Scene Presets override Default Volume Levels. Press Play, turn ON, etc. Room Output volume ahon all the way down Increase volume.

Speakers in room miswired or defective a. Test known good speaker at back panel speaker connector b. Verify connections No audio present in any cla4 Hum or buzz through system speakers Poor audio quality 26 1. See above Perform steps above 2. Atonn speakers most likely cause. Verify that the impedance levels of the amp and speaker are not lower than 8 Ohms. Ground loop Ensure proper grounding using a three prong grounded AC outlet.

  KINESIOLOGIA HOLISTICA PDF

Speakers out of phase Carefully check polarity of each speaker 3. Functions this way to protect amplier. IR signal not reaching Room input. Check Room IR receiver and verify wiring. Remote Control batteries are dead. IR Control No source control in any Room. Source IR Emitters unplugged or defective. Reconnect or test with known good IR Emitters.

Mild to moderate IR Flooding. Check IR indicator on front panel.

If it ickers, IR ooding is indicated. Check any IR receivers that may be receiving ambiant light or plasma TV noise. Room appears to be on and selected but unabled to be controlled using front panel buttons. The IR indicator will be solid red when the room is off, solid off when the room is on, or solid purple when the room is on and unselected.

Remote Control batteries are dead Replace batteries 1. Position of Receiver base not optimal Move Receiver base to nd optimum placement. Carefully peel the appropriate Room Identication Label from the card and place it in the Room Label Location for the chosen room.

Remote Control Aaton Option 1: It is not necessary to point the remote at the main unit in order for it to function.

ATON Stereo Receiver DLA4 User Guide |

Place the receiver in a convenient location; preferably as high as possible. The RF Receiver Base utilizes mounting holes to mount vla4 unit to a wall, cabinet or other surface. Programming additional remotes can be accomplished in a matter of seconds. Local Commands control only one room at a time.

Use Rack screws not included to attach the assembled unit to the equipment rack as shown in Figure D If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly contacts ATON at or service atonhome. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement. Warranty service requests made without proof of date of purchase will be denied.

Lda4 keep the original sales receipt for your records and send a copy to request warranty service. Dlq4 a community-based project which helps to repair anything.